Optimum parameter matching obtained by experiments for coring drilling into lunar simulant

This paper performs a series of ground experiments (on the Earth) to obtain optimum parameter matching for a future core drill on the Moon. Three common stages, I, II, III, are recognized with respect to the cut per revolution (CPR), which is defined as the ratio between the feeding speed and the rotating speed. The optimum matching between the feeding speed and the rotating speed for drills locates at the boundary position between Stage II and Stage III, where the coring rate saturates and the weight on the bit and the driving torque are still low. Further data analysis of the ground experiments reveals that the optimum matching signifies a proportional relation between the maximum conveying rate (MCR) by the groove of the auger and its rotating speed. The kinetic analysis in an ideal condition without gravity, the friction from the auger groove and the pressure at the bit confirm a similar proportion. The correlation between the proportions needs further study to determine whether the optimum matching obtained on the ground can be directly applied to future drills on the Moon.     

Design and experimental study of a micro-groove grinding wheel with spray cooling effect

The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming.     

环型与线型聚能装药射流成型机理对比

环型聚能装药药型罩2侧在挤压汇聚形成射流过程中存在不对称性,不能完全套用线型聚能装药射流成型的现有理论。利用DYNA3D软件对相同剖面结构的环型、线型聚能装药射流成型过程进行数值模拟,通过比较分析得出了环型聚能装药形成杵体及射流参数的分布特性,为进一步理论研究及工程应用提供参考。     

钢球连接方式火工装置的结构强度校核

文章介绍了钢球连接方式火工装置中，钢球连接处的结构强度校核。通过经典的接触应力计算公式，结合钢球在火工装置上的具体使用情况，利用微变形理论，归纳出了火工装置上起连接承载作用的钢球连接方式新的强度校核判断法则。试验结果表明，该判据能够较为真实地反映火工装置上钢球连接方式的结构承载能力。     

机匣沟槽对微型轴流涡轮叶尖泄漏流动的影响

本文通过对某微型涡喷发动机的单级轴流式涡轮进行机匣设计,采用剪切应力输运(SST)模型求解定常黏性雷诺平均Navier-Stokes方程,研究了不同机匣沟槽结构对其叶尖泄漏流动的影响。计算结果说明：当全机匣沟槽结构的叶顶浸入沟槽即d/c＞1.0时,封严效果较好;相较于全机匣沟槽结构,后开式机匣沟槽结构的封严效果更好, 随着沟槽前缘间隙的增大,封严效果减弱;沟槽深度a/c=1时,封严效果最佳,即泄漏流明显减弱,同时效率减小量较小。     

双发进气道抽吸试验系统及流量高精度测量技术

针对常规进气道试验方法存在流量测量精度低、综合试验能力差等诸多问题,及无法满足不同类型进气道在不同工况下开展性能试验的需要的状况,建立了一套应用于TBCC等双发发动机进气道风洞试验的抽吸试验系统及流量高精度测量技术.系统采用文氏流量计测量方法,以提高进气道流量测量的精度;采用在流量计末端直接加装中压环形引射器抽吸进气道主气流的方法,以满足不同类型进气道在不同工况下对吸入流量的需求;通过设计两套独立的管道系统并分别进行流量的测量与控制,以满足双发进气道不同工况性能匹配和耦合试验的需求.通过风洞验证试验验证了流量计的测量效果和引射器的引射能力,通过风洞应用试验验证了试验系统对不同形式进气道的综合试验能力.试验结果表明,试验系统测量精度高,引射抽吸能力和综合试验能力强,能全面满足各类进气道风洞试验的需求.     

侧载及加热方位对槽道内临界热流密度影响

为了研究侧载以及加热方位对矩形窄缝槽道内临界热流密度特性的影响,在旋转平台上进行了两相流的超重力实验.以蒸馏水为工质,通过改变质量流速、入口温度、侧载大小以及加热方位,获得了发生临界换热现象时的质量流速、实验段压降和壁温的变化趋势,考察了侧载和加热方位对临界热流密度的影响规律,并对侧载下两相流不稳定性进行了简析.实验表明:发生临界换热时,壁温迅速上升,有效加热热流开始减少,关闭加热电源后,实验段压降下降、质量流速回升较明显;侧载以及不同的加热方位对临界热流密度有明显影响;临界热流密度发生前后,蒸汽回流导致进口温度上升,增加了流动的不稳定性.      

扇形段与全环燃烧室熄火性能换算研究

为研究不同类型燃烧室试验件熄火性能之间的关系,开展了扇形段和全环燃烧室的熄火性能试验.通过试验对比了二者熄火规律的相似性和差异性,并分析了造成差异的主要因素.以Lefebvre熄火模型为基础,结合雾化数据,拟合得到扇形段与全环燃烧室的贫油熄火经验关系式,并推算出二者熄火性能的定量换算公式.结果表明:扇形段与全环燃烧室的熄火边界变化规律类似,但在相同的工作状态条件下,全环燃烧室的贫油熄火油气比小于扇形段的相应值.     

冲压发动机点火前内流场数值仿真研究

冲压发动机在点火前由于燃烧室的压力较低,内通道流场状态与发动机正常工作时的差别很大。因此,在发动机设计时,必须要考虑形成正常点火条件对发动机结构的约束。本文利用有限体积法对N-S方程进行空间离散,对发动机点火前的不同内通道结构下的冷流场进行了数值模拟,结果表明稳定器和喷油装置对形成合理的点火条件很重要,稳定器的布局对点火状态有很大影响。     

试论规范高校内部审计责任

本文结合高校内部审计工作实际，论述了规范高校内部审计责任的现实意义。指出规范高校内部审计责任的内涵及其存在的问题。提出了加强规范高校内部审计责任的几项措施。